Fire pump inspection, testing and maintenance
Fire pumps are used to ensure an adequate water supply by increasing pressure for fire
suppression and, as such, are an integral part of the fire protection system for a facility. Failure of
a fire pump to operate under fire conditions can result in a major loss. To help ensure the fire or
booster pump is working, there needs to be periodic inspection, maintenance and testing of the
pump. The following information provides an overview of the requirements; a separate checklist
for electric pump and diesel pump is attached at the end of the document.
Download a PDF for printable checklists.
Who can perform the inspections and testing
NFPA 25, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems, states that inspection testing and maintenance should be performed by a qualified person who has developed competence through training and experience. Many companies use a qualified outside contractor for the annual flow test on a pump and use in-house personnel for the weekly or monthly tests. Some states require that the person conducting the annual fire pump test be certified.
What needs to be done
Inspection, testing, and maintenance requirements are outlined in NFPA 25, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems. Below is an overview of the inspection and testing activities that should be completed on your pump. A detailed checklist for an electric pump and diesel pump follow on subsequent pages.
Weekly
- Pump house, heating, ventilating louvers
- Fire pump system
- Pump Operation (Diesel only)—no flow start and run test for 30 minutes
Monthly
- Pump Operation (Electric only)—no flow start and run test for 10 minutes
Annual
- Full flow test both diesel and electric pumps
- Fire pump alarm signals
Maintenance
- On an annual basis service hydraulic systems, mechanical transmission and motor
- All other maintenance on the pump and associated components varies and should be completed in accordance with the manufacturers’ recommendations.
Hanover risk solutions can help
Your Risk Solutions consultant can meet with you to explain the inspection, testing, and maintenance requirements based on the fire protection systems installed at your facility. They can discuss the options with you for helping to ensure that your systems are adequately maintained. See attached checklists or download a print version.
Diesel pump inspection, maintenance* and testing—weekly visual inspection
| EQUIPMENT | CONDITION |
| Pump House | Heat not less than 40ºF (with engine heater) OR Heat not less than 70ºF (no engine heater) |
| Ventilating Louvers | Operating freely |
| Housekeeping | Room free of combustible storage |
| Valves | Pump suction, discharge and bypass valves fully open |
| Piping | Free of leaks |
| Suction Line | Pressure gauge normal |
| Reservoir/Tanks (If applicable) | Suction reservoir or tank full |
| Controller Pilot Light | Light Pilot light (power on) illuminated |
| Fuel Tank | Fuel tank at least two-thirds full |
| Controller | Selector switch in “AUTO” position |
| Batteries |
|
| Alarm Pilots | Alarm pilots off |
| Engine Oil | Engine oil is full |
| Cooling Water | Cooling water is full |
| Engine Running Time Meter | Meter is reading |
| Jockey Pump (If provided) | Power to jockey pump |
*MAINTENANCE: maintenance of the pump and its components should be in accordance with the manufacturers’ recommendations.
Weekly no flow (“churn”) test
| EQUIPMENT | CONDITION |
| Pump |
|
| Record pressures readings |
|
| Pump glands | Slight discharge when running |
| General pump function | No unusual noises or vibration |
| Packing Box, bearings, and pump casings | No signs of overheating in packing box, bearings, or pump casings |
| Heat Exchanger | Cooling water flow |
Annual
| EQUIPMENT | CONDITION |
| Full Flow test | Date of test results satisfactory? |
To learn more about Hanover Risk Solutions, visit hanoverrisksolutions.com
The recommendation(s), advice and contents of this material are provided for informational purposes only and do not purport to address every possible legal obligation, hazard, code violation, loss potential or exception to good practice. The Hanover Insurance Company and its affiliates and subsidiaries ("The Hanover") specifically disclaim any warranty or representation that acceptance of any recommendations or advice contained herein will make any premises, property or operation safe or in compliance with any law or regulation. Under no circumstances should this material or your acceptance of any recommendations or advice contained herein be construed as establishing the existence or availability of any insurance coverage with The Hanover. By providing this information to you, The Hanover does not assume (and specifically disclaims) any duty, undertaking or responsibility to you. The decision to accept or implement any recommendation(s) or advice contained in this material must be made by you.
LC JAN 2019 13-01
171-0854 (1/15)